进口潜水轴流泵美国潜水轴流泵

进口潜水轴流泵技术参数：

流量：350-46800m3/h
扬程：1.5-20m
口径：500-1600
转速：245-1450、2900
功率：22-1400kw
电压：380V、600V、6KV、10KV
介质温度：50℃

进口潜水轴流泵工作原理：

是传统的水泵电动机组的更新换代产品，驱动水泵的电动机是干式全封闭潜水三相异步电动机，该型潜水电泵可*浸入水中运行。具有传统机组一系列*的优点。

（1）由于电机与水泵构成一体，现场安装方便、快捷，同传统机组相比可节约95%安装时间。

（2）由于电机潜入水中运行，电机冷却条件好，泵站内无高温，噪音低，可建成地下泵站，保持地面环境风貌，大大简化泵站的土工及建筑结构工程，减少安装面积，节约工程造价30-40%

（3检测信号集中反馈于电控柜的监控器内，操作方便，易于实现自动控制及远传控制。

进口潜水轴流泵特点：

轴流泵在零流量时的轴功率zui大，因此泵在启动前必须先打开排出管路上的阀，以减小启动功率。轴流泵主要适用于低扬程、大流量的场合，如灌溉、排涝、船坞排水、运河船闸的水位调节，或用作电厂大型循环水泵。扬程较高的轴流泵可供浅水船舶的喷水推进之用。

进口潜水轴流泵美国泰乐TYLER售后服务：

*的服务铸就*的企业让客户无后顾之忧。
1、按合同要求提供产品的合格证、铭牌、检验报告、产地证名、安装说明书等。
2、顾客在验收产品过程中，如出现与合同要求不符时，我司接到顾客通知后两小时内给予处理。
3、我司提供十二个月以上产品质保期，时间从验收合格之日起计算。
4、在正确安装和使用下，出现产品质量问题，本公司将负责到底。

Imported submersible axial flow pump

Technical parameters of imported submersible axial flow pump:

Flow: 350-46800m3/h

Lift: 1.5-20m

Caliber: 500-1600

Speed: 245-1450, 2900

Power: 22-1400kw

Voltage: 380V, 600V, 6KV, 10KV

Medium temperature: 50

Working principle of imported submersible axial flow pump:

Is the traditional water pump motor group replacement products, drive the pump motor is dry full closed submersible three-phase asynchronous motor, the submersible pump can be immersed in water for a long time to run. With a series of incomparable advantages of traditional units.

(1) because of the integration of the motor and the pump, the installation is convenient and fast, and it can save the installation time by 95% compared with the traditional unit.

(2) because the motor run in the water, cooling conditions, pump station without high temperature, low noise, can be built underground pumping station, maintain the ground environment, greatly simplifying the geotechnical and structural engineering of pumping station, reducing installation area, save the project cost 30-40%

(3 detection signal feedback on the monitor in centralized control cabinet, convenient operation, easy to realize automatic control and remote control.

Imported submersible axial flow pump:

Axial flow pump at zero flow when the shaft power is the largest, so the pump must be opened before the start of the discharge pipe on the valve to reduce the starting power. Axial flow pump is mainly used in low lift and large flow situations, such as water, irrigation and drainage, drainage, dock canal lock regulation, or as power plant circulating water pump. Axial flow pump with high lift can be used for water jet propulsion of shallow water ship.

The United States imported submersible axial flow pump of tylosin TYLER customer service service:

The first-class service created a first-class enterprise so that customers no worries.

1, according to the contract requirements for product certification, nameplate, inspection report, certificate of origin, installation instructions etc..

2, the customer in the process of acceptance of the product, such as the emergence of the contract requirements and inconsistent, I received the notification of the customer within two hours after the treatment.

3, our company provides more than twelve months warranty period, the time from the date of acceptance.

4, in the correct installation and use, product quality problems, the company will be responsible in the end.

进口潜水轴流泵guan网：http://www.twvalve。。ｎｅｔ/html/2288.html