60T双缸液压打包机60吨立式双缸液压打包机 
废纸打包机，
 配用动力：11KW，
台时产量：3-5个包块，
包重：200-300KG，
油缸：Φ150*2支，
操作方便，机器使用46#或者68#液压油，用量90kg液压油，
 接上电源后打包 , 于一切轻泡、松散物料的打包。可应用于棉、羊毛、废纸、废纸箱、废纸板、纱线、塑料、布匹、编织袋、针织绒、麻、麻袋、毛条、毛球、茧、蚕丝、啤酒花、麦柴、草、废塑料袋等一切轻泡、松散物料。包型紧凑，整齐美观，可大幅降低运输成本，是棉产区、纺织企业、超市、服装厂、废旧物资回收业和其他各种轻工业企业*的生产工具 。
60吨
型号：60
公称压力主缸KN：600
液体zui大工作压力MPa:15
料箱尺寸长900mm,宽650mm,高:1400mm
包块尺寸:长900mm*宽:650 *高:(500-1000）mm
包块密度kg/m3：≥500
单次循环时间S：36
电机功率KW：11
油缸行程：1000MM
机器外形尺寸mm：长1550*宽1100*高3200。
整机重量kg；2200.
液压打包机使用说明
安装步骤
1、本机必须平稳放在混凝土上，基础视当地情况决定。
2、检查油箱底部放油口是否已关闭，确定关闭后再打开油箱顶部加油口密封盖。
注入约90KG,68#液压油，液压油排号视当地气温及使用标准决定。[注！如果机型在60T以上，新机时必须分两次注油，*次注入液压油高度至油尺顶部（蓝色界线）。待压板下压至底部再加注液压油至油尺底部（红色界线）详细见操作说明4]
3、安装好本机电源线,电压及频率视当地电源决定，（注！电机和电器配件的电压及频率已按客户订购机器时的要求配置安装好）常规采用三相四线制，其中三条带电源线分别接入电相内相应的三个接线位，（图7左）另一条为接地防漏电保护线，应紧接机体外露金属表面，以防电器漏电伤人。
操作方法：
1、通入电源：把电箱内空气开关（本机总开关）合上，先检查三相电源电压是否正常，（用仪表或探电笔测试）关闭电相门，查看电相门板表面红色电源指示灯是否亮起。
2、启动电机：把手动换向阀手柄（付图3）往下推至zui底位（机体附有操作图标），然后把启动按钮NO按下（图5右下），（注：如装有急停开关机型的请把急停开关按箭头方向右旋，急停开关弹出即可），（图5右上）如正常情况下电机启动。
3、 检看电机转向：（图8）电机启动后，手动换向阀手柄在zui下位时，如压板不能往下移。这时请必须立即查看电机旋转方向是否正确，电机旋转方向必须按箭头指示方向*。如果电机转向相反时则机器不能正常使用，这时应把手动换向阀手柄往上拉至中档位。然后按下停止按钮OFF（或急停开关按下）停止电机运转。切断输入总电源，把三相电源线其中二相线互换再接上即可。再按操作1和2重新操作，（注！必须确定电机转向是否与箭头指示方向*。）
4、注入油量的关健：当压板正常往下移时，压板在*次移动，移动速度是不均匀的。待压板移至底部或移动中突然停止又或移动中噪声加大，这种情况下应先把手动换向阀手柄往上拉至中位，把停止开关OFF或急停开关按下，停止电机运行。再仔细查看油箱储油量是否足够，如油量底于油箱高度一半时，证明油量不足，这时应再次往油箱注入适当液压油。这次加油量应加至油位尺zui底界线（红色界线）即可。

60 tons of vertical double cylinder hydraulic baler
Waste paper baler,
 Equipped with power: 11KW,
Taiwan when the output: 3-5 mass,
Package weight: 200-300KG,
Cylinder: Φ150 * 2,
Easy to operate, the machine uses 46 # or 68 # hydraulic oil, the amount of 90kg hydraulic oil,
 Connected to the power after packaging, dedicated to all light foam, loose material packaging. It can be used in cotton, wool, waste paper, waste paper box, waste paperboard, yarn, plastic, cloth, woven bag, knitted cashmere, hemp, sack, top, hair ball, cocoon, silk, hops, , Waste plastic bags and all the light foam, loose material. It is a necessary production tool for cotton producing areas, textile enterprises, supermarkets, garment factories, waste materials recycling industry and other light industrial enterprises.
60 tons of double cylinder hydraulic baler
Model: 60
Nominal pressure master cylinder KN: 600
Liquid maximum working pressure MPa: 15
Box size 900mm long, 650mm wide, high: 1400mm
Package Size: Length 900mm * Width: 650 * Height: (500-1000) mm
Mass density kg / m3: ≥ 500
Single cycle time S: 36
Motor power KW: 11
Cylinder travel: 1000MM
Machine dimensions mm: Length 1550 * Width 1100 * Height 3200.
Machine weight kg; 2200.
Hydraulic baler instructions
First, the installation steps
1, the machine must be placed on the concrete, the basic depending on the local situation.
2, check the bottom of the fuel tank is closed, to determine the closure and then open the top of the tank filling port seal.
Injection of about 90KG, 68 # hydraulic oil, hydraulic oil row number as the local temperature and the use of standards. [Note! If the model is above 60T, the new machine must be filled with oil twice, the first time into the hydraulic oil height to the top of the dipstick (blue line). Press the press down to the bottom and then add the hydraulic oil to the bottom of the dipstick (red border) see the operating instructions in detail 4]
3, the installation of the local power cord, voltage and frequency depending on the local power supply decision, (Note! Motor and electrical parts of the voltage and frequency of customer orders have been ordered to install the machine installed) conventional three-phase four-wire system, three With the power cord, respectively, into the electrical phase of the corresponding three wiring bits (Figure 7 left) and the other for the ground leakage protection line, should be exposed to the body exposed metal surface to prevent electrical leakage wounding.
Second, the operation method:
1, access to power: the air box inside the air switch (the main switch) to close, first check the three-phase power supply voltage is normal, (with a meter or probe pen test) to close the electrical phase door, see the power of the door surface red power Whether the indicator light is on.
2, start the motor: the manual valve handle (pay Figure 3) down to the bottom (the body with the operation icon), and then press the button NO button (Figure 5 lower right), (Note: if installed There are emergency stop switch models, please put the emergency stop switch in the direction of the arrow, the emergency stop switch can pop up), (Figure 5 on the right) as normal under the motor start.
3, check the motor steering: (Figure 8) After the motor starts, manual valve handle in the lowest position, such as the pressure plate can not move down. In this case, you must immediay check whether the direction of rotation of the motor is correct and the direction of rotation of the motor must be in the direction indicated by the arrow. If the motor turns to the opposite when the machine can not be used normally, then the manual valve handle should be pulled up to the mid-range position. Then press the stop button OFF (or the emergency stop switch is pressed) to stop the motor from running. Cut off the total input power, the three-phase power cord which can be connected to the two-phase line. And then press operations 1 and 2 to re-operate, (Note! Must determine whether the motor steering direction is consistent with the arrow.)
4, into the fuel of the key: When the pressure plate down the normal move, the pressure plate in the first move, the movement speed is not uniform. To be pressed to move to the bottom or move suddenly stop or move the noise increases, in which case the manual valve should be pulled up to the middle of the handle, stop the switch OFF or emergency stop switch, stop the motor run. And then carefully check the tank oil storage is sufficient, such as oil at the end of the fuel tank height of half, to prove that the amount of oil, then again should be injected into the tank appropriate hydraulic oil. The amount of fuel should be added to the bottom line of the oil level (red line) can be.