QC12Y液压摆式剪板机
产品简介
详细信息
产品特点：
1、优质钢材焊接，摆式刀架，强度高、刚性好；
2、焊后消除内应力,机身整体加工，保证了加工精度；
3、刃口间隙无极调整，轻便快速；
4、后挡料电动调整数字显示；
5、具有剪切计数定数功能，使用方便；
6、具有灯光照明功能，便于划线剪切；
7、定制的压料脚，可以有效保护板料不被压伤，离刀片较近，便于压窄料。
技术参数：
| QC12Y Series Hydraulic swing beam shearing machine | ||||||
| Specification | Shearing thickness (mm) | Shearing width （mm） | Shearing angler （°） | Number of Stroke （min-1） | Backguage range （mm） | Motor power（KW） |
| QC12Y/K-4*2500 | 4 | 2500 | 1°30′ | 20 | 20-600 | 4 |
| QC12Y/K -4*3200 | 4 | 3200 | 1°30′ | 18 | 20-600 | 5.5 |
| QC12Y/K -4*4000 | 4 | 4000 | 1°30′ | 18 | 20-600 | 7.5 |
| QC12Y/K -6*2500 | 6 | 2500 | 1°30′ | 18 | 20-600 | 7.5 |
| QC12Y/K -6*3200 | 6 | 3200 | 1°30′ | 14 | 20-600 | 7.5 |
| QC12Y/K -6*4000 | 6 | 4000 | 1°30′ | 14 | 20-600 | 7.5 |
| QC12Y/K -6*5000 | 6 | 5000 | 1°30′ | 10 | 20-800 | 11 |
| QC12Y/K -6*6000 | 6 | 6000 | 1°30′ | 10 | 20-800 | 11 |
| QC12Y/K -8*2500 | 8 | 2500 | 1°30′ | 14 | 20-600 | 7.5 |
| QC12Y/K -8*3200 | 8 | 3200 | 1°30′ | 10 | 20-600 | 7.5 |
| QC12Y/K -8*4000 | 8 | 4000 | 1°30′ | 8 | 20-600 | 7.5 |
| QC12Y/K -8*5000 | 8 | 5000 | 1°30′ | 7 | 20-800 | 11 |
| QC12Y/K -8*6000 | 8 | 6000 | 1°30′ | 6 | 20-800 | 22 |
| QC12Y/K -10*2500 | 10 | 2500 | 1°30′ | 14 | 20-800 | 11 |
| QC12Y/K -10*3200 | 10 | 3200 | 1°30′ | 12 | 20-800 | 11 |
| QC12Y/K -10*4000 | 10 | 4000 | 1°30′ | 12 | 20-800 | 11 |
| QC12Y/K -10*6000 | 10 | 6000 | 2° | 10 | 20-800 | 15 |
| QC12Y/K -12*2500 | 12 | 2500 | 1°30′ | 16 | 20-800 | 18.5 |
| QC12Y/K -12*3200 | 12 | 3200 | 1°30′ | 14 | 20-800 | 18.5 |
| QC12Y/K -12*4000 | 12 | 4000 | 1°30′ | 14 | 20-800 | 18.5 |
| QC12Y/K -12*5000 | 12 | 5000 | 2° | 7 | 20-1000 | 30 |
| QC12Y/K -12*6000 | 12 | 6000 | 2° | 6 | 20-1000 | 37 |
| QC12Y/K -12*8000 | 12 | 8000 | 2°30′ | 5 | 20-1000 | 37 |
| QC12Y/K -16*2500 | 16 | 2500 | 2° | 16 | 20-650 | 18.5 |
| QC12Y/K -16*3200 | 16 | 3200 | 2° | 12 | 20-800 | 22 |
| QC12Y/K -16*4000 | 16 | 4000 | 2° | 10 | 20-800 | 30 |
| QC12Y/K -16*6000 | 16 | 6000 | 2° | 8 | 20-800 | 30 |
| QC12Y/K -20*2500 | 20 | 2500 | 2°30′ | 5 | 20-1000 | 30 |
| QC12Y/K -20*3200 | 20 | 3200 | 2°30′ | 4 | 20-1000 | 30 |
| QC12Y/K -20*4000 | 20 | 4000 | 2°30′ | 3 | 20-1000 | 37 |
| QC12Y/K -20*6000 | 20 | 6000 | 2°30′ | 3 | 20-1000 | 45 |
| QC12Y/K -25*2500 | 25 | 2500 | 2°30′ | 6 | 20-1000 | 45 |
| QC12Y/K -25*3200 | 25 | 3200 | 2°30′ | 5 | 20-1000 | 45 |
| QC12Y/K -25*4000 | 25 | 4000 | 3° | 5 | 20-1000 | 45 |
| QC12Y/K -32*2500 | 32 | 2500 | 3° | 5 | 20-1000 | 55 |
| QC12Y/K -32*3200 | 32 | 3200 | 3° | 4 | 20-1000 | 55 |
| QC12Y/K -40*2500 | 40 | 2500 | 4° | 5 | 20-1000 | 75 |
| QC12Y/K -40*3200 | 40 | 3200 | 4° | 3 | 20-1000 | 90 |
| QC12Y/K -50*3200 | 50 | 3200 | 3° | 5 | 20-1000 | 90*3 |
| QC12Y/K -50*6000 | 50 | 6000 | 3° | 5 | 20-1000 | 90*5 |
| QC12Y/K -60*3200 | 60 | 3200 | 3°30′ | 5 | 90*4 | |
| Because in the continuous improvement of products, if there is difference between this date and technical data, should comply with the technical agreement parameters on both sides. No further notice! | ||||||